How long are the spin poles for a 17, 19 and 20tr?? Also, about what angle are they in comparison to the beams?
I know Bill won't like it, but I'm considering putting a Hooter on my 19 and 20tr and a friend is looking to add one to his 17.
Thanks in advance..
Search found 214 matches
- July 11th, 2005, 10:10 am
- Forum: Technical Forum
- Topic: Spin poles
- Replies: 1
- Views: 3878
- June 27th, 2005, 9:39 am
- Forum: General Discussion
- Topic: A New Owner of an Old Supercat 17
- Replies: 2
- Views: 4430
SCs in VA
I'm in Va Beach and I have a SC19 and a SC20TR. There are a few 17s around, too. The factory is the best place for spare parts, but there is also a SC fleet Fleet 15) near Annapolis. You'll have to hunt them down on line, but there is someone in the fleet that has a bunch of parts. You can contact R...
- May 19th, 2005, 7:58 am
- Forum: Technical Forum
- Topic: SC20 decks
- Replies: 14
- Views: 15149
- May 19th, 2005, 7:55 am
- Forum: Technical Forum
- Topic: SC20 decks
- Replies: 14
- Views: 15149
- May 18th, 2005, 9:58 pm
- Forum: Technical Forum
- Topic: SC20 decks
- Replies: 14
- Views: 15149
- May 18th, 2005, 9:57 pm
- Forum: Technical Forum
- Topic: SC20 decks
- Replies: 14
- Views: 15149
Much better Photos!!
OK, this one is of the section near the rear beam..
- May 18th, 2005, 9:55 pm
- Forum: Technical Forum
- Topic: SC20 decks
- Replies: 14
- Views: 15149
- May 18th, 2005, 3:56 pm
- Forum: Technical Forum
- Topic: SC20 decks
- Replies: 14
- Views: 15149
- May 10th, 2005, 8:03 am
- Forum: Technical Forum
- Topic: SC20 decks
- Replies: 14
- Views: 15149
Matt, My boat is an 81 Tall Rig. I can see that the plate was cut out very cleanly, so it looks factory. I'm thinking that there was some repair work done to the trunks, because there is also a cut-out in the plate near the dagger well opening. I think that after time, it just cracked, so I'm not to...
- April 28th, 2005, 11:50 am
- Forum: Technical Forum
- Topic: SC20 rigging
- Replies: 0
- Views: 6521
SC20 rigging
I am considering getting new rigging for my '80 SC20 TR. Are the rigging lengths available?? I want to measure everything before I take the plunge.
- April 28th, 2005, 7:11 am
- Forum: Technical Forum
- Topic: SC20 decks
- Replies: 14
- Views: 15149
SC20 decks
I noticed a few cracks on the decks of my SC20 under the non-skid. I did some sanding in the area to fill them and it looks like there were some holes cut in the deck--possibly to get to the dagger trunk. However, the more I sanded, I found the outline of the hole to get much bigger. It looks as if ...
- February 28th, 2005, 1:16 pm
- Forum: Technical Forum
- Topic: SC20 Daggers
- Replies: 3
- Views: 5385
- February 28th, 2005, 8:53 am
- Forum: Technical Forum
- Topic: SC20 Daggers
- Replies: 3
- Views: 5385
SC20 Daggers
I was flipping through my owner's manual the other day and it indicated that the daggers for the 20 are marked for each side. I can't see any difference in the two that I have and I have had some made that are exactly alike. Are they really different, or were they fitted for a specific side??
- February 24th, 2005, 9:31 am
- Forum: General Discussion
- Topic: just checking in..
- Replies: 2
- Views: 3977
Nacra
Eric,
I have 3 5.2 hulls that I don't know what to do with. I'm working on a SC19 and SC20, so I would trade for any extra parts. Heck, if you can pick them up, you can have them! I'm in Va Beach and will be in Atlanta for the Spring Fever race over Easter...
Dan
danberger@mindspring.com
I have 3 5.2 hulls that I don't know what to do with. I'm working on a SC19 and SC20, so I would trade for any extra parts. Heck, if you can pick them up, you can have them! I'm in Va Beach and will be in Atlanta for the Spring Fever race over Easter...
Dan
danberger@mindspring.com
- January 5th, 2005, 1:32 pm
- Forum: Technical Forum
- Topic: SC20TR spreader conversion
- Replies: 1
- Views: 3905
SC20TR spreader conversion
I am considering switching my spreaders from the 3 spreader set-up to the Arc22 single spreader set-up with pre-bend. If I do this, would I have to get a new main that is cut for the pre-bend, or can I go ahead and use the standard cut Dacron main?
Does anyone have a good used 22 main for sale??
Does anyone have a good used 22 main for sale??